|

ASHDOWN was designed by Mark Gooday,
well known in the world of bass amplification and for his involvement
in the development of Trace Elliot. ASHDOWN offers
a wide array of amps, cabs, preamps, and power amps. These combine the
sound of tubes and solid state electronics with a unique feature, the Sub-Harmoniser,
resulting in a wide range of fat, deep tones.
ASHDOWN is used and endorsed by a multitude
of pro players including John Entwistle, Mark King, Adam Clayton, Roger
Waters, and Mathew Garrison.
 |
The ABM 500 EVO II is a 575 watts RMS bass amp head designed to satisfy both bass-purists and tech-heads alike. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out, and flat/shaped by footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones.
Also footswitchable is the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 500 EVO II features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
Retail $1149 Sale Price $805
|
|
 |
The ABM 900 EVO II is a 575+575 watts RMS bass amp head designed to satisfy both bass-purists and tech-heads alike. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out, and flat/shaped by footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones.
Also footswitchable is the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 900 EVO II features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
Retail $1449 Sale Price $1015
|
|
|

|
For those requiring an integrated solution, the ABM 500RC EVO II is a rack-mounting version of the standard ABM 500 EVO II Head, with a stunning, polished chrome panel. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out, and flat/shaped by footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones. Also footswitchable is the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 500RC EVO II features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
Retail $1149 Sale Price $805
|
|

|
575 Watt Mono Magnifier Head EVO III
Retail $1799 Sale Price $1259
| Power Output (RMS) |
575W |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
310 x 470 x 240 |
| Weight (kg) |
16 |
|
|

|
575 watts x 2 Twin Channel Magnifier Head EVO III Retail $2259 Sale Price $1582
| Power Output (RMS) |
575 + 575W |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
340 x 610 x 240 |
| Weight (kg) |
24 |
|
|

|
500 Watt 1x15 Super Compact Cabinet, Neo Lite at 8 Ohms
Retail $1599 Sale $1299
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the compact, 350-Watt, 1 x 15 Neo MINI 15 cabinet is the use of a new, custom developed Neodymium speaker which incorporates a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is an ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
350W |
| Speaker Configuration |
1 x 15 Neo |
| Impedance |
8 Ohms |
| H x W x D (mm) |
585 x 475 x 335 |
| Weight (kg) |
21 |
|
|

|
500 Watts, 115 with a Tweeter,Neo Superdrive Lite 8 Ohm Retail $1749 Sale Price $1399
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the 400-Watt, 1 x 15 + horn Neo-115h cabinet is the use of a new, custom developed Neodymium speaker which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
400W |
| Speaker Configuration |
1 x 15 Neo +horn |
| Impedance |
8 Ohms |
| H x W x D (mm) |
730 x 610 x 420 |
Retail $1549 / Sale $1085
|
|

|
600 Watt, 4x8 Super Compact Cabinet, NEO Lite at 8 Ohms
Retail $1899 Sale Price $1499
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the compact, 1000-Watt, 4 x 8 Neo MINI 48 cabinet is the use of new, custom developed Neodymium speakers which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
1000W |
| Speaker Configuration |
4 x 8 Neo |
| Impedance |
8 Ohms |
| H x W x D (mm) |
585 x 475 x 335 |
| Weight (kg) |
25 |
|
|

|
800 Watt, 4x10 W/Horn Super Drive Light, 8 Ohms
Retail $2099 Sale Price $1469
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the 1050Watt, 4 x 10 + horn Neo-410h cabinet is the use of new, custom developed Neodymium speakers which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
1050W |
| Speaker Configuration |
4 x 10 + horn |
| Impedance |
8 Ohms |
| H x W x D (mm) |
730 x 610 x 420 |
| Weight (kg) |
37 |
|
|

|
800 Watt, 4x10 W/Horn Super Drive Light, 4 Ohms
Retail $2099 Sale Price $1469
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the 4 Ohm, 1050-Watt, 4 x 10 + horn Neo-414h cabinet is the use of new, custom developed Neodymium speakers which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
1050W |
| Speaker Configuration |
4 x 10 + horn |
| Impedance |
4 Ohms |
|
|

|
1600 Watts, 8x10 NEO Superdrive Lite at 4 Ohms
Retail $3449 Sale Price $2414
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
Central to the performance of the 1050-Watt, 8 x 10, Neo-810 cabinet is the use of new, custom developed Neodymium speakers which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a ultra-lightweight bass driver that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
1050W |
| Speaker Configuration |
8 x 10 |
| Impedance |
4 Ohms |
| H x W x D (mm) |
1280 x 610 x 420 |
| Weight (kg) |
60 |
|
|

|
200 watts 1x10 speaker. Sale $199
|
|
 |
Retail $579 Sale Price $405
The ABM 115 COMPACT is a 300 watt 8 Ohm bass cabinet featuring a single 15"
Ashdown BlueLine driver in a precision tuned plywood cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. Special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
| Power Handling |
300W continuous, 600W programme |
| Speaker Configuration |
1 x 15" |
| Frequency Response |
41Hz - 4kHz |
| Impedance |
8 Ohms |
| SPL |
94dB 1W@1m |
| H x W x D (mm) |
474 x 610 x 420 |
| Weight (kg) |
28 |
|
|
 |
The ABM 115 is a 300 watt 8 Ohm bass cabinet featuring a single 15" Ashdown BlueLine driver in a precision tuned plywood cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. Special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
| Power Handling |
300W continuous, 600W programme |
| Speaker Configuration |
1 x 15" |
| Frequency Response |
37Hz - 2kHz |
| Impedance |
8 Ohms |
| SPL |
98dB 1W@1m |
| H x W x D (mm) |
661 x 610 x 420 |
| Weight (kg) |
33 |
|
|
 |
The ABM 210T COMPACT is a 300 watt 8 Ohm bass cabinet combining 2 X 10"
Ashdown BlueLine drivers with an HF tweeter in a precision tuned plywood cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. Special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
| Power Handling |
350W continuous, 700W programme |
| Speaker Configuration |
2 x 10" + HF tweeter |
| Frequency Response |
75Hz - 20kHz |
| Impedance |
8 Ohms |
| SPL |
102dB 1W @ 1m |
| H x W x D (mm) |
474 x 610 x 420 |
| Weight (kg) |
28 |
|
|
 |
The ABM 410T is a 600 watt 8 Ohm bass cabinet combining 4 X 10" Ashdown BlueLine drivers with an HF tweeter in a precision tuned plywood cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. Special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
| Power Handling |
650W continuous, 900W programme |
| Speaker Configuration |
4 x 10" + HF tweeter |
| Frequency Response |
70Hz - 20kHz |
| Impedance |
8 Ohms |
| SPL |
103dB 1W @ 1m |
| H x W x D (mm) |
661 x 610 x 420 |
| Weight (kg) |
36 |
|
|
 |
Retail $1399 Sale Price $979
The ABM 810 is a 1200 watt 4 Ohm bass cabinet featuring 8 X 10" Ashdown BlueLine drivers in a precision tuned plywood cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. Special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
| Power Handling |
1200W continuous, 1800W programme |
| Speaker Configuration |
8 x 10" |
| Frequency Response |
70Hz - 4kHz |
| Impedance |
4 Ohms |
| SPL |
109dB 1W @ 1m |
| H x W x D (mm) |
1150 x 610 x 430 |
| Weight (kg) |
77 |
|
|

|
575 Watt 1x15,Neo Superdrive Lite EVO III
Retail $2799 Sale Price $1959
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
The 575-Watt, 1 x 15 C115-500 combo features a single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. A built-in dual band compressor acts separately on the high and low frequency components of the signal to provide precise control, while the on-board sub-harmonic generator turns the Classics into powerhouses of tone.
The inclusion of a 4-way footswitch as standard makes Ashdown Classic amongst the most versatile live performance bass amps in the business, providing control over the compressor, sub-harmonic generator, tube grind and EQ pre-shape.
Central to the performance of the combo is the use of a new, custom developed Neodymium speaker which incorporates a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is an ultra-lightweight bass drivers that just keeps getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
575W |
| Speaker Configuration |
1 x 15 |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
645 x 610 x 340 |
| Weight (kg) |
36 |
|
|

|
575 Watt Combo 4x10 with a Horn, Neo Superdrive Lite EVO III Retail $3199 Sale Price $2239
Proudly built in the UK, the Classic Series is Ashdown’s flagship bass amp range. Comprising of 500 and 1000-watt Klystron heads, a selection of cabinets and a range of 500-Watt combos, the Classics are about doing everything better – more volume, more dynamics, an extended frequency range and greater versatility.
The 575-Watt, 4 x10 + horn C410H-500 combo features a single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. A built-in dual band compressor acts separately on the high and low frequency components of the signal to provide precise control, while the on-board sub-harmonic generator turns the Classics into powerhouses of tone.
The inclusion of a 4-way footswitch as standard makes Ashdown Classic amongst the most versatile live performance bass amps in the business, providing control over the compressor, sub-harmonic generator, tube grind and EQ pre-shape.
Central to the performance of the combo is the use of new, custom developed Neodymium speakers which incorporate a number of advanced features including a cast aluminium chassis with thin brackets to avoid sound wave reflections, a magnet circuit with heat sink rims to ensure rapid heat dissipation and decompression holes in the cone. The result is a range of ultra-lightweight bass drivers that just keep getting louder as the level is increased, delivering a powerful, consistent bass tone at all volume levels and with no power loss over long performances.
| Power Output (RMS) |
575W |
| Speaker Configuration |
4 x10 + horn |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
340 x 825 x 610 |
| Weight (kg) |
47 |
|
|
 |
The ABM C115-500 EVO II combo combines the features of the ABM 500 EVO II head with a single 15" Ashdown BlueLine driver in a precision tuned cabinet.
The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. All amplifier chassis are built from heavy-duty 16 swg zinc coated mild steel, foil lined to minimise interference, and special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
The ABM 500 EVO II is a 575 watts RMS bi-amp bass amp head designed to satisfy both bass-purists and tech-heads alike. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out, and flat/shaped by footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones.
Also footswitchable is the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 500 EVO II features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
| Power Output (RMS) |
575W |
| Speaker Configuration |
1 x 15 |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
645 x 610 x 340 |
| Weight (kg) |
36 |
|
|
 |
The ABM C210-500 EVO II combo combines the features of the ABM 500 EVO II head with 2 X 10" Ashdown BlueLine drivers plus HF tweeter in a precision tuned cabinet. The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. All amplifier chassis are built from heavy-duty 16 swg zinc coated mild steel, foil lined to minimise interference, and special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
The ABM 500 EVO II is a 575 watts RMS bi-amp bass amp head designed to satisfy both bass-purists and tech-heads alike. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out, and flat/shaped by footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones.
Also footswitchable is the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 500 EVO II features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
| Power Output (RMS) |
575W |
| Speaker Configuration |
2 x10 + horn |
| Frequency Response |
-3dB at 17Hz and 30kHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9m Ohms, input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10k Ohms, input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms, input level 0dBu nominal |
| Line Output |
Impedance 10k Ohms, level 0dBu nominal |
| DI Output |
600 ohms balanced, level -20dBu nominal |
| Tuner Output |
Impedance 1k Ohms, level 0dBu nominal |
| EQ |
Bass +/-15dB @ 45Hz
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 110Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms, input level 0dBu nominal |
| H x W x D (mm) |
645 x 610 x 340 |
| Weight (kg) |
37 |
|
|
 |
Retail $1499 Sale Price $1049
Legendary UK bassist Mark King was a major inspiration for Ashdown Labs bass amplification, and we're proud to present Mark's own Signature Series amplifier.
Forming a platform for the development of the AL-AD600 bass amp head, Ashdown Labs worked in consultation with Mark to build an amplifier which met his requirements for absolute fidelity and clarity, precision tone shaping and masses of power on tap for stunning dynamics. The result is the AL-MK500, a 575 Watts RMS funk powerhouse with low impedance instrument input, illuminated VU meter, Harmonic Emphasis, 12-band graphic EQ, switchable pre and post EQ balanced DI output, tuner output with mute switch, line output, effects loop and speaker outputs on jack and Speakon connectors.
"This amp takes my sound to a whole new level" reports a delighted Mr King.
"It's so dynamic, so alive!"
| Power Output (RMS) |
575W / 900W Peak |
| Line Input |
Impedance 3.9M Ohms, Input range 150mV to 20V P-P |
| Line Output |
Impedance 1K Ohms, Level 0dBu Nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms / Level 0dBu nominal |
| Output Impedance |
4 Ohms |
| EQ |
+/– 15dB @ 12 Centre Frequencies |
| Effects Send |
Impedance 22k Ohms / Level 0dBu nominal |
| Effects Return |
Impedance 10K Ohms / Level 0dBu Nominal |
| H x W x D (mm) |
195 x 525 x 325 |
| Weight (kg) |
14 |
XLR Input
Digital Output |
Impedance Balanced 600 Ohms, Input range 100mV to 10V p-p
None |
|
|

|
300 Watt Bass Amp Head Mag Pre Amp
Retail $569 Sale Price $399
The MAG 300H head features a potent new fan-cooled 307 watts RMS power section. Rotary bass, middle and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, providing a comprehensive 5 band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to attacking and warm, rounded sounds respectively and, on the subject of low-end response, the trademark Ashdown sub-harmonic generator is ready and able to deliver truck loads of earth moving tone if called upon. Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.
With the MAGs now achieving EVO II status, the amplifier also includes a built-in compressor with precision sonic control.
The cabinet is protected by a tough carpet covering.
| Power Output (RMS) |
307W |
| Power Requirement |
230 /115v |
| Frequency Response |
-3dB at 17Hz and 30KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms / Level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms / Level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
90 x 463 x 267 |
| Weight (kg) |
8.5 |
|
|

|
600 Watt Bass Amp Head Mag Pre Amp
Retail $699 Sale Price $489
The MAG 600H head features a potent new fan-cooled 575 watts RMS power section. Rotary bass, middle and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, providing a comprehensive 5 band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to attacking and warm, rounded sounds respectively and, on the subject of low-end response, the trademark Ashdown sub-harmonic generator is ready and able to deliver truck loads of earth moving tone if called upon. Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.
With the MAGs now achieving EVO II status, the amplifier also includes a built-in compressor with precision sonic control.
The cabinet is protected by a tough carpet covering.
| Power Output (RMS) |
575W |
| Power Requirement |
230 /115v |
| Frequency Response |
-3dB at 17Hz and 30KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms / Level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms / Level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
90 x 483 x 267 |
| Weight (kg) |
12 |
|
|
 |
Rated at 8 Ohms with a power handling of 300 watts, the new MAG115 1 x 15"
cabinet is now built 'Extra Deep' and loaded with an Ashdown BlueLine speaker for exceptional attack, clarity and low-end performance. Protection is provided by tough black carpet covering and new steel grilles.
| Power Handling |
250W continuous |
| Speaker Configuration |
1 x 15" |
| Frequency Response |
37Hz - 2kHz |
| Impedance |
8 Ohms |
| SPL |
98dB 1W @ 1m |
| H x W x D (mm) |
468 x 604 x 420 |
| Weight (kg) |
27 |
Retail $369 Sale Price $258
|
|
 |
Deep
Rated at 8 Ohms with a power handling of 300 watts, the new MAG210T 2 x 10"
+ tweeter cabinet is now built 'Extra Deep' and loaded with Ashdown
+ BlueLine
speakers for exceptional attack, clarity and low-end performance. Protection is provided by tough black carpet covering and new steel grilles.
| Power Handling |
250W continuous |
| Speaker Configuration |
2 x 10" + tweeter |
| Frequency Response |
60Hz - 20kHz |
| Impedance |
8 Ohms |
| SPL |
98dB 1W @ 1m |
| H x W x D (mm) |
468 x 604 x 420 |
| Weight (kg) |
29 |
Retail $369 Sale Price $258
|
|
 |
Deep
Rated at 8 Ohms with a power handling of 400 watts, the new MAG410T 4 x 10"
+ tweeter cabinet is now built 'Extra Deep' and loaded with Ashdown
+ BlueLine
speakers for exceptional attack, clarity and low-end performance. Protection is provided by tough black carpet covering and new steel grilles.
| Power Handling |
450W continuous |
| Speaker Configuration |
4 x 10" + tweeter |
| Frequency Response |
60Hz - 20kHz |
| Impedance |
8 Ohms |
| SPL |
101dB 1W @ 1m |
| H x W x D (mm) |
655 x 604 x 420 |
| Weight (kg) |
37 |
Retail $429 Sale Price $300
|
|

|
The ideal partner for the MAG 650 head, the MAG 810 cabinet is loaded with 8 Ashdown 10" BlueLine speakers for unparalleled low end performance, clarity and attack.
| Power Handling |
800W continuous |
| Speaker Configuration |
8 x 10" |
| H x W x D (mm) |
1125 x 609 x 420 |
| Weight (kg) |
65 |
Retail $839 Sale Price $587
|
|
 |
Retail $719 Sale Price $503
The MAG C115-300 1 x 15" combo features a potent new fan-cooled 575 watts RMS power section. Rotary bass, middle and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, providing a comprehensive 5 band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to attacking and warm, rounded sounds respectively and, on the subject of low-end response, the trademark Ashdown sub-harmonic generator is ready and able to deliver truck loads of earth moving tone if called upon. Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.
All MAG combos have extension speaker outputs and are loaded with Ashdown BlueLine speakers for exceptional attack, clarity and low-end performance.
Protection is provided by tough black carpet covering and new steel grilles, while the amplifier chassis is constructed from light yet strong, heat-dissipating magnesium alloy for 'roadie-free' portability. And, of course, the famous Ashdown VU meter remains central to the cool look of these great, value for money bass amplifiers.
| Power Output (RMS) |
307W |
| Power Requirement |
230 / 115V |
| Speaker Configuration |
1 x 15" BlueLine speaker |
| Frequency Response |
-3dB at 17Hz and 30KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms, level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
581 x 474 x 300 |
| Weight (kg) |
28 |
|
|
 |
Retail $849 Sale Price $594
The MAG C210T-300 2 x 10" + tweeter combo features a potent new fan-cooled
575 watts RMS power section. Rotary bass, middle and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, providing a comprehensive 5 band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to attacking and warm, rounded sounds respectively and, on the subject of low-end response, the trademark Ashdown sub-harmonic generator is ready and able to deliver truck loads of earth moving tone if called upon.
Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.
All MAG combos have extension speaker outputs and are loaded with Ashdown BlueLine speakers for exceptional attack, clarity and low-end performance.
Protection is provided by tough black carpet covering and new steel grilles, while the amplifier chassis is constructed from light yet strong, heat-dissipating magnesium alloy for 'roadie-free' portability. And, of course, the famous Ashdown VU meter remains central to the cool look of these great, value for money bass amplifiers.
| Power Output (RMS) |
307W |
| Power Requirement |
230 / 115V |
| Speaker Configuration |
2 x 10" BlueLine speaker + tweeter |
| Frequency Response |
-3dB at 17Hz and 30KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms, level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
581 x 610 x 335 |
| Weight (kg) |
35 |
|
|
 |
Retail $949 Sale Price $665
The MAG C410T-300 4 x 10" + tweeter combo features a potent new fan-cooled
575 watts RMS power section. Rotary bass, middle and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, providing a comprehensive 5 band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to attacking and warm, rounded sounds respectively and, on the subject of low-end response, the trademark Ashdown sub-harmonic generator is ready and able to deliver truck loads of earth moving tone if called upon.
Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.
All MAG combos have extension speaker outputs and are loaded with Ashdown BlueLine speakers for exceptional attack, clarity and low-end performance.
Protection is provided by tough black carpet covering and new steel grilles, while the amplifier chassis is constructed from light yet strong, heat-dissipating magnesium alloy for 'roadie-free' portability. And, of course, the famous Ashdown VU meter remains central to the cool look of these great, value for money bass amplifiers.
| Power Output (RMS) |
307W |
| Power Requirement |
230 / 115V |
| Speaker Configuration |
4 x 10" BlueLine speaker+ tweeter |
| Frequency Response |
-3dB at 17Hz and 30KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms, level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms, level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
768 x 610 x 335 |
| Weight (kg) |
44 |
|
|
 |
Retail $589 Sale Price $412
Ashdown Electric Blue bass amplification loads legendary Ashdown tone into an affordable new amp head and a pair of high-performance, high-value combos. The EB 12-180 1 x 12" combo uses a 180 Watts RMS fan-cooled fast-transient power stage, and a fully-featured bass preamplifier with inputs for both active and passive instruments, an illumunated VU meter, 5 band EQ with Bright and Deep switches, a front panel-mounted balanced DI output for connection to a PA or recording console, an FX loop, a tuner/line output and the classic Ashdown sub-harmonic generator.
A high-performance Ashdown BlueLine bass driver ensures exceptional attack, clarity and low-end performance, while an extension speaker output can be used to connect an additional cabinet for use in larger venues. The cabinet is finished in a tough, scuff-proof carpet covering with protective corners and a kick-proof metal grille.
| Power Output (RMS) |
180W |
| Power Requirement |
230 /115v |
| Speaker Configuration |
1 x 12" BlueLine speaker |
| Frequency Response |
-3dB at 33Hz and 25KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms, level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms / Level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
501 x 474 x 300 |
| Weight (kg) |
27 |
|
|
 |
Ashdown Electric Blue bass amplification loads legendary Ashdown tone into an affordable new amp head and a pair of high-performance, high-value combos.
The EB 15-180 1 x 15" combo uses a 180 Watts RMS fan-cooled fast-transient power stage, and a fully-featured bass preamplifier with inputs for both active and passive instruments, an illumunated VU meter, 5 band EQ with Bright and Deep switches, a front panel-mounted balanced DI output for connection to a PA or recording console, an FX loop, a tuner/line output and the classic Ashdown sub-harmonic generator.
A high-performance Ashdown BlueLine bass driver ensures exceptional attack, clarity and low-end performance, while an extension speaker output can be used to connect an additional cabinet for use in larger venues. The cabinet is finished in a tough, scuff-proof carpet covering with protective corners and a kick-proof metal grille.
| Power Output (RMS) |
180W |
| Power Requirement |
230 /115v |
| Speaker Configuration |
1 x 15" BlueLine speaker |
| Frequency Response |
-3dB at 33Hz and 25KHz |
| Speaker Outputs |
Minimum impedance 4 Ohms |
| High Instrument Input |
Impedance 3.9MOhms / Input range 150mV - 20V p-p |
| Low Instrument Input |
Impedance 10KOhms / Input range 300mV - 40V p-p |
| Line Input |
Impedance 22k Ohms / Input level 0dBu nominal |
| DI Output |
600 Ohms balanced / Level -20dBu nominal |
| Tuner Output |
Impedance 22k Ohms / Level 0dBu nominal |
| Signal to noise |
Better than 80dB (EQ flat) |
| EQ |
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 220Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz |
| Effects Send |
Impedance 22k Ohms / Level 0dBu nominal |
| Effects Return |
Impedance 22k Ohms / Level 0dBu nominal |
| Distortion |
Less than 0.5% THD |
| H x W x D (mm) |
581 x 474 x 300 |
| Weight (kg) |
29 |
|
|

|
15 Watt 8" Combo W/Extention Speaker And CD Input
Retail $249 Sale Price $174
The After Eight bass practice amp combines a 15 watt power section with a single 8" Ashdown BlueLine bass speaker. Sounds can be shaped quickly and intuitively using bass, middle and treble controls, supplemented by a pre-shaped 'deep' switch. A headphone output is provided for private practice along with an extension speaker output.
| Power Output (RMS) |
15W |
| Speaker Configuration |
1 x 8" |
| Line Input |
Impedance 1M Ohm, Input range 100mV to 10V |
| H x W x D (mm) |
415 x 378 x 405 |
| Weight (kg) |
14.65 |
|
|
TN.jpg)
|
30 Watt 10 " Combo W/Extention Speaker And CD Input
Retail $349 Sale Price $244
The Perfect Ten bass practice amp combines a 30 watt power section with a single 10" Ashdown BlueLine bass speaker. Sounds can be shaped quickly and intuitively using bass, middle and treble controls, supplemented by a pre-shaped 'deep' switch. A headphone output is provided for private practice along with an extension speaker output.
| Power Output (RMS) |
30W |
| Speaker Configuration |
1 x 10" |
| Line Input |
Impedance 1M Ohm, Input range 100mV to 10V |
| H x W x D (mm) |
505 x 444 x 500 |
| Weight (kg) |
21.43 |
|
|

|
100 Watt 15 " Combo W/Extention Speaker And CD Input
Retail $429 Sale Price $300
Named in memory of our late, great friend John Entwistle, the Five Fifteen bass practice amp combines a 100 watt power section with a single 15" Ashdown BlueLine bass speaker. Sounds can be shaped quickly and intuitively using bass, middle and treble controls, supplemented by a pre-shaped 'deep' switch. A headphone output is provided for private practice along with an extension speaker output.
| Power Output (RMS) |
100W |
| Speaker Configuration |
1 x 15" |
| Line Input |
Impedance 1M Ohm, Input range100mV to 10V |
| H x W x D (mm) |
550 x 459 x 544 |
| Weight (kg) |
26.8 |
|
|
|
|
|
| |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|